Our Brand TM Pleated Shade Style 1 inch Poplin with Privacy Liner

Our Brand Poplin 1 inch Pleated Shade collection is a fabric that is a woven semi private fabric. Adding Privacy liner will provide some light control and full privacy. Seamless out to 72 inches but a wider blind can be phone ordered and priced but it will be manufactured with seams. Liners are not needed on Quartz, Moon Dance, and Tusk because they are pre-lined and room darkening.

View Price Grid

Factory Allowances and Deductions

Inside Mount Outside Mount Headrail Less 1/2" Ordered Size Slats Less 1/2" Ordered Size Valance Less 1/8" Plus 1 1/2"   + or - 1/8" variance   Blinds that measure 12 1/8"" - 17 7/8" net must have split controls Blinds that measure 7" - 12" net require center wand tilt only-cord

Blind Specifications

Headrail Size............................................2" x 2 1/4"

Minimum Width .....................................7" Net

Maximum Width(single blind)..............96"

Minimum Length....................................12'

Maximum Length....................................126"

Minimum Return Length.......................1/2"

Standard Return Length........................2 7/8"

Recommended Single Blind Width......72"

Important Ordering Information

- Blinds manufactured over 84" wide as a single blind are not covered under our warranty.

- Multiple blinds on one headrail over 108" is not recommended - Order these blinds as two or three separate blinds with one common valance.

- A headrail brace is recommended for blinds over 70" wide.

- Blinds or single valances produced over 94" wide will be charged additional shipping charges.

Mounting Requirements

Minimum Mounting Space...............1 1/8"

Flush Mounting Space Req'd...........3"

Outside Mount Flat Space Req'd.....2 1/4"

Features

Standard Cord / Wand tilt optional

2 on 1 and 3 on 1 Headrail available

Cotton Tapes available as a upgrade

Cut- out available (charged per cut-out)

Color Coordinated Contoured Bottomrail

Matching Crown Valance

Wooden Tassels

Ladder Spacing Charts

Blind Width (net) # of Ladders # of Cords Routless # of Cords 7" - 32" 2 2 4 32 1/8" - 56" 3 2 3 56 1/8" - 78" 4 4 4 78 1/8" - 96" 5 4 4 Important Note: Certain wood stain blinds are specifically manufactured with darker clored braided ladder. Instances of dye transference from ladder to slat have occured and are not considered to be a defect or warranty issue.

 

Tips To Remember:

Use a steel measuring tape
Round down to the nearest 1/8" for width
Round up to the nearest 1/8" for height
See Product Specifications for more specific product info.
Sizes should always be provided in this format: Width x Height
On any measurement given, the factory does have a +/- 1/8 of an inch variance allowance.

Measure For Pleated Shades

Inside Mount Width

•    Measure the exact width (left to right) of the inside edge of the window frame in three places (top, middle and bottom).
•    Take the smallest of the three measurements to the nearest 1/8 of an inch.
•    The factory will take an approximate 3/8 of an inch deduction from the total width (headrail and fabric) to allow for correct installation.

Inside Mount Height

•    Measure the exact height (top to bottom) from the top inside edge down to the window sill in three spots across window.
•    Take the largest of the three measurements.

Outside Mount Width

•    Measure the exact width (left to right) of the wooden or metal window frame (outer edge) OR how wide you want the product to be.
•    Be sure to measure wide enough as to cover the entire window plus offer enough coverage to avoid light or privacy gap. This is especially important if you have no trim and are installing to sheet rock or dry wall surface. 1-2 inches past the opening on EACH side is suggested if you do not have molding/trim.
•    French doors-you should have a minimum of 1 inch past the glass on each side added to the glass measurement for coverage.

Outside Mount Height

•    Measure the top and bottom edge of window frame/trim. If no trim, be sure you provide the height you want the shade to be from top of the headrail to bottom of the bottom rail.
•    Be sure to allot for coverage for light control and mounting hardware if mounting above window opening to wall surface. You will need 2 inches of surface area to mount above opening. Call us for further instruction if needed.
•    French doors-Be sure to add 2 inches for mounting above glass on surface of door for installation brackets and 2 inches below for hold down bracket install.-Call us for more information on this type of install.
 

Installation Instructions